Sứ cách điện (Electrical Insulators) chính là những "người hùng thầm lặng" của lưới điện quốc gia. Nếu không có chúng, chúng ta sẽ không thể tận hưởng những tiện ích cơ bản hàng ngày như sạc điện thoại hay thắp sáng ngôi nhà của mình. 💡
Hôm nay, hãy cùng Handyman khám phá quy trình sản xuất cực kỳ tinh vi để tạo ra những linh kiện quan trọng này qua bài dịch chi tiết từ chuyên gia Andy Schwalm (Giám đốc Công nghệ tại Victor Insulators, Inc.):
📖 QUY TRÌNH CHẾ TẠO: SỨ CÁCH ĐIỆN ĐƯỢC LÀM RA NHƯ THẾ NÀO?
1️⃣ Chuẩn bị nguyên liệu: Quy trình bắt đầu với hỗn hợp nguyên liệu thô gồm đất sét, fenspat (tràng thạch) và silica. Chúng được trộn với nước để tạo thành một hỗn hợp bùn lỏng gọi là "slip".
2️⃣ Lọc ép (Filter Pressing): Hỗn hợp bùn được ép qua các khung lọc để loại bỏ nước dư thừa, tạo thành các bánh đất sét dẻo và đặc. 3️⃣ Tạo hình (Forming): Đất sét được đưa vào máy đùn chân không để loại bỏ bọt khí, sau đó được cắt thành phôi và đặt lên máy quay để tạo hình dáng đặc trưng với các đường rãnh đồng tâm (giúp tăng bề mặt cách điện).
4️⃣ Sấy khô & Tráng men: Sau khi sấy khô chậm để tránh nứt vỡ, sứ được nhúng vào lớp men gốm. Lớp men này không chỉ giúp bề mặt nhẵn bóng để tự làm sạch khi mưa mà còn tăng độ bền cơ học cho sản phẩm.
5️⃣ Nung (Firing): Sản phẩm được nung trong lò ở nhiệt độ cực cao. Quá trình này làm thay đổi cấu trúc hóa học của đất sét, biến nó thành vật liệu gốm cứng, bền và có khả năng cách điện tuyệt vời.
6️⃣ Lắp ráp & Kiểm tra: Cuối cùng, các bộ phận kim loại được gắn vào sứ bằng xi măng đặc chủng. Mỗi sản phẩm đều phải vượt qua các bài kiểm tra nghiêm ngặt về khả năng chịu tải điện và độ bền kéo trước khi xuất xưởng.
🛒 BẠN ĐANG TÌM KIẾM THIẾT BỊ ĐIỆN & PHỤ KIỆN CÁCH ĐIỆN CHUYÊN NGHIỆP?
Đừng để công trình của bạn thiếu đi sự an toàn và chất lượng! Mọi giải pháp về thiết bị điện công nghiệp, vật tư cách điện và dụng cụ thi công cao cấp đều đã có mặt tại Handyman.vn.
🔹 Tại sao nên chọn mua sắm tại Handyman?
✅ Vận hành bởi DLV Corporation – Đơn vị uy tín hàng đầu trong lĩnh vực cung ứng vật tư công nghiệp tại Việt Nam.
✅ Sản phẩm chính hãng, đạt tiêu chuẩn chất lượng quốc tế (tương tự các dòng sản phẩm của Grainger).
✅ Đội ngũ tư vấn kỹ thuật chuyên sâu, hỗ trợ tận tâm cho mọi dự án.
✅ Chính sách bảo hành và giao hàng nhanh chóng, đáng tin cậy.
👉 Ghé thăm ngay cửa hàng trực tuyến: Handyman.vn để trang bị những thiết bị tốt nhất cho công việc của bạn!
You’ve definitely seen them, and you've probably wondered what they are. They have an odd, cylindrical shape, like a stack of teacups or discs, attached to utility poles or high voltage transmission lines. These are insulators, and Andy Shwalm knows a thing or two about them.
Andy is the technical director of the oldest insulator manufacturer in the U.S. Located in Victor, New York, Victor Insulators has been in the business since 1893 and still ships about 10,000 tons of product per year. Andy explained what insulators do and demonstrated the precision and craft that go into manufacturing these essential pieces of our electrical infrastructure.
This interview has been edited for clarity.
The Importance of Insulators
Overhead power lines are insulated by air. It’s the air gap around them that prevents electricity from flowing or arcing from the lines to somewhere you don’t want it to go. What an insulator does is to maintain that air gap.
Without insulators, we wouldn’t be able to transmit electricity from where it’s generated to where it’s used. You wouldn’t have electricity for air conditioning, running the lights or charging your phone.
An insulator needs to be totally nonconductive, and it needs to withstand the voltage without ever breaking down. And the shape of the insulator is important. The shape is designed to have a lot of creepage – that’s the distance along the insulator’s surface from the conductor end to the ground end. Having a large creepage distance prevents arcing that would flash over the insulator. And the shape also helps prevent the accumulation of rainwater, snow or dirt that can interfere with the insulating properties.
The Raw Materials
We’re using raw materials, which are quite literally dug up out of the ground, to make a finished product. There are three kinds of materials that we use. We get them as powders.
The main group is clays, which provide the plasticity. Then there’s the fluxing agent, which is feldspar, basically decomposed granite. Then there’s the filler material. We use two different fillers, silica sand and aluminum oxide.
When we mix these materials and fire them in a kiln, what's happening is that the feldspar and the clays react to form a glassy phase, and that glassy phase surrounds the filler particles. Ultimately, the fired porcelain is a glassy phase with filler particles of either silica or aluminum oxide embedded in it.
Mixing the Clay
For porcelain to happen, we need to mix the materials as finely and completely as we can, which means using a very large amount of water. We mix it into something that looks like a milkshake. At this point it’s about 50% water by weight.
Then we need to take most of that water back out. We filter-press it back down to about 16% to 18% water. That gives us a stiff clay.
We also need to get the air out of the clay. We run it through a vacuum extruder, which shreds the clay up under a vacuum and recompacts it into a cylinder.
These cylinders can be shaped on a lathe or other turning tool. For some shaping processes, we need to dry the clay first. We dry it very slowly. If it dries too fast it will crack, like a mud puddle heating up in the sun.
Firing the Cylinders
Porcelain is an odd material because it doesn't exist naturally. To make it exist, you need to put a tremendous amount of energy into it. It requires chemical reactions that don’t want to happen.
Heat is what drives those chemical reactions forward. The kilns fire at about 2,300 degrees F, and our products are in there from three to six days.
All the heat energy that goes into making porcelain is also one of the reasons it’s such a good insulating material. It takes so much energy to make it, and it takes just as much to unmake it. That’s why you can dig up a Ming vase that’s hundreds of years old and still intact.
The composition of porcelain also makes it nonporous, which is important for us. You can put one of our insulators in a tub of water and leave it there for 50 years – it will absorb absolutely no moisture. This is critical for insulators because moisture and electricity do not mix.
Controlling the Dimensions
We add metal fittings to some of our insulators. For example, a switch manufacturer might want to install the insulator on his product, so we would need to put metal fittings on it.
During the assembly stage, we need to ensure the dimensional integrity of the insulator. It sounds easy to say, “I'm just going to cement two metal caps on a piece of porcelain,” but there are requirements for the orientation of the caps, the length of the insulator, the parallelism of the caps. There are a bunch of characteristics that need to be maintained, so the process is not that simple. We need to control all the critical dimensions.
Testing and Shipping the Product
Every single insulator is tested prior to shipment to ensure its integrity. Some of the testing is very simple. We flash over the insulator at ultra-high frequency or three to five minutes at 60 cycle frequency, just to ensure there are no defects. Other products, such as large station posts, we’ll mechanically test at about 50% of their rated strength.
Porcelain is somewhat fragile, so packaging is very important, both for handling the product and protecting the product. One of our real costs is packaging. We’re always working on how we can adequately protect the product in an efficient way.
#Handyman #DLVCorporation #ElectricalInsulators #SuCachDien #KyThuatDien #HowItsDone #VatTuCongNghiep #AnToanDien